How To Reset Xfinity Remote?

Posted on: 19 Jul 2024

How to Change a Lost Xfinity Remote

If your Xfinity remote is unresponsive, behaves erratically where for instance it does not change the channels correctly, turns off the TV or is generally not functional as it should, try resetting it. Re- forming your Xfinity remote is quite effective and often restores the working of the remote. Below are the procedures that are followed when trying to reset different models of Xfinity TV Packages remotes.

A Step-by-Step Guide in Relearning How to Use a New Traditional Xfinity Cable Box Remote

Switch on your Television set and cable reception set. Ensure that both devices are on before attempting to reset the remote in question because this is important. If your remote cannot turn on either one, you will have to turn on the device using a button on the device.
On the back part of the remote control, you will find a very small button labeled as “Setup. ” It should be in the bottom right corner, beside the page number that is placed in the bottom right corner. This is followed by, press and hold this button until the LED status light at the top of the remote blinks twice, then release. This means that the remote has power and has been reset to default settings.
The last step is to point the remote at the cable box to ensure that it functions correctly. Plug the power and channel buttons into the cable box to test if the remote controls it sufficiently. If the remote is working, the status light on the same has to blink when sending the commands.
If those functions are still not working, try to get your Xfinity remote to pair again. Enter the device brand name by dialing the required code number and then typing the code number of the brand of your TV/equipment. The issue may have been fixed after pairing; again conduct a test to confirm the result.

How Does One Reset an X1 Voice Remote

The X1 Voice remote comes with a reset button that one may use in case the remote hitches.

Here is how to use it:

Ensure that you have your TV on and your cable box/DVR is also on. The relative motion you need power to devices that the remote control to be effective.
Take the TV remote control and turn it over to its back side and try to look at the bottom part. Finding a small circular button whose function is only to reset the device.
The next instruction to be followed is to press and hold the reset button for about 10 seconds. The LED status light on the remote will blink for approximately 5 seconds and then turn solid after which the LED status light will start blinking rapidly if you continue holding the Reset button for the next 5 seconds, the LED status light will stop blinking and turn solid once you release the Reset button after about 10 seconds.
The remote will then go through the 10 second reset and turn off, but will automatically power back on immediately. The status light will go out and then flash rapidly once the LED strip starts working again.
Try to use the voice commands or buttons to operate your devices to ensure if the reset helped the remote control to regain its functionality.

Restarting an XR2 or XR5 Remote

Both the XR2 and the XR5 come with a reset button on the remotes which can be immediately pressed whenever they are not responding appropriately. Follow these steps:

Check whether there is power supply flowing to the TV, cable box, or other devices that relate to the remote control unit. To operate it, you need to approach the device and stand in front of it.
Do the same but while pressing the Xfinity button together with the Mute button for about 5 seconds. Hold the button and when the status light starts to flash and release the button when the light is continuously solid again.
The remote will sustain the reboot and immediately afterward, viewers will see more blinks as the remote reboots and reconnects.
After the status light turns off again, test the Remote and make sure it works properly by trying to change channels, turn on/off your TV or cable box. If problems are not solved, reset the device and re-assign it to the appropriate tool.

To Reset an XG1v4 or XR15 Remote:

If you have the model XG1v4 or XR15 voice remote that's not responding correctly, utilize this reset method:If you have the model XG1v4 or XR15 voice remote that's not responding correctly, utilize this reset method:

It is also important to ensure that all the equipments that are connected to the remote are on, before attempting the reset. Make sure you stand where you’re in front of the devices.
To turn volume down quickly, locate the two triangular buttons of Volume Down and Back on the side of the phone and press them down together.
Hold these buttons for least 5 seconds until the LED near the top of the product starts blinking several times.
After establishing the flashing pattern at a high rate, remove your fingers from the button. Thus, the remote will reboot itself in a few seconds.
Wait for the LED to blink and turn off, then point the whole at the devices to check the ability to change volume and channels. Give voice commands if it is possible in that specific model of car and watch for improvements if any.

Reconnection – XR11 or XR11v3 remote

Make sure the devices are switched on – they may have powered off to save energy and be ready to accept the signals from the remote. Holding the remote close to these powered-on devices will provide the best signal reception when the remote is in malfunctions.
Locate and push at the same time with your thumb/finger the Xfinity and Info buttons. Press these buttons for a slow count of 10 second.
Within about 5 seconds of its powering up, a green status light positioned at the top of the device will brighten up steadily. Hold it for a few seconds more before total 10 seconds is up; when that’s done, both buttons can be released.
Thus, the remote will start blinking rapidly and shut off the status light, indicating its restarting process. In a couple of seconds, functionality should be restored since it reconnects with your devices again.
Try to use channel/volume commands and go to voice control, if available. If there are issues persisting with control problems then reset again.

Ways to avoid the need to perform the remote resets often

Yes, it is convenient to have quick reset buttons on Comcast Xfinity remotes – but it is even more disruptive to have to restart them on a regular basis. Use these tips to avoid needing frequent resets:Use these tips to avoid needing frequent resets:

Also, batteries should always be checked and replaced with fresh batteries when some of them are exhausted in order to ensure uniform performance. The low battery levels can presuppose the failures of the remote.
Clean the remote more often with disinfecting wipes, as they are likely to contain skin oils, food particles and grime that affects hardware buttons and voice mics.
Update the remote software when required to keep up with changes to cable boxes, DVRs and other TV hardware that can receive firmware changes as well.
Do not immerse your remote in any fluids as this may lead to internal system damage and subsequent erratic functioning. Do not expose remotes with any internal moisture to their circuits and any electronic equipment in the house or building.
Maintain clear LOS paths of the RF link between the remote and the devices being controlled. Any large coverage gaps in the room can cause some level of hinderance in the actual communication.
Switch to another replacement remote if resetting could not bring back the function after checking for hardware difficulties. Nonfunctional buttons, the status of the lights, and voice components suggest that the machine requires a warranty replacement.

Powering reset your Xfinity remote does not take a lot of time irrespective of your remote model. For the respective hardware remote, these procedures can allow connectivity to be restored in most instances or to regain control of equipment in a home theater system. Remember the relevant reset procedure described herein, for the Xfinity remote style you possess.

Ready to elevate your home entertainment? Call us now at +1 844-345-0888 to explore the best Xfinity plans for your home! Enjoy fast internet and premium TV options. Don’t wait—get connected today!